86-0769-39020536
NFC access control card simulator crack version how to download? How to install NFC access simulator? The NFC Emulator (NFC Emulator) is a software that can emulate a mobile phone as an access control card. This application allows the phone to have an unlocked access card. The NFC Access Card Simulator Cracked APK file is sorted out here, and is available for download. Please attach the usage method and tutorial. I hope that you can simulate the success and never worry about forgetting to bring the access control card.
Download address: Link """ (here is the latest version of 4.0.7, this version does not break)
1, if you need to successfully simulate, you first need to obtain root privileges, individual models need to unlock the system.
2, the software has a writing function, you can avoid the root to achieve access control simulation, pay attention to smart white card access control, white card needs to be purchased from the software development author.
3, Before using the NFC access simulator, if the phone does not respond to the card access control card, or if the mobile phone's access control is not responding, it can be predicted that the door cannot be opened successfully. The current access control system may not be applicable.
4. There is no response to the mobile phone's brush access control. It may be that some models can only implement the card simulation in the HCE mode. You need to switch the mobile phone to the HCE mode (recommended to use the built-in SE).
5, In addition, it cannot be successfully opened. It is also possible that the access control system has a high degree of intelligence and can identify the copy card.
7. Before using, you can use NFC taginfo to detect whether the access card has encrypted information. If there is encryption setting, it cannot be successfully simulated.
Introduction to the working principle of NFC access card simulatorThe application mainly uses the card number information of the analog IC access control card. Note that only the card number information can be used to store the information in the card. Therefore, it is applicable to the access control system for identifying the IC card number. Most of the current domestic access control systems use this method. Therefore, it can successfully replace the access control card, but the offline stored value function cannot be used. It cannot simulate bank cards, meal cards, water cards, bus cards, parking cards, etc.
NFC Access Card Simulator Usage TutorialBasic operation: Enter the application through the QQ login authorization operation. After the login is successful, you can upload and download card information. You can chat and post in the community. The software registration information is bound to QQ.
The software has an access card editing function that can delete, modify, create new cards, support export, share, and create shortcuts.
The software has a custom adaptation file function, the software can adapt to most models, but some models still can not be adapted, you need to manually add the adaptation file, if you encounter this situation, it is recommended to contact the author.
NFC Access Card Simulator Simulate Card Steps1, root your phone, there are a lot of root online tutorials, do not start here to speak, to find their own information root, there is an official root try to use the official root, third-party root will lead to software Caton, if encountered Caton, There is no official root program friend, please use kingroot.
2, if the program has obtained root privileges, but still suggest that the system file can not be written, then you also need to unlock the system, currently seems only the millet system needs this.
3. Here, the operating environment of the software has basically been settled. Note that if the following steps encounter problems, you can empty the program data and rerun it. This can solve many problems.
4, now you can go to get your access control card to brush, in the main interface of the program to swipe, the program will automatically save the card, and then click to start simulation, will pop up the saved card for you to choose, choose a card and then determine The program will automatically simulate, if the prompt simulation is successful, then basically your operation is already correct; if the software prompts you can not find the NFC control file, you can use the software to customize the adaptation file function, the specific method see below Customize the adaptation file paragraph. If you have any questions, please contact the author for advice.
5. If the prompt simulation is successful, there will be a beep when swiping the card. Your access control system may be encrypted. The software only simulates the card number. The encrypted content cannot be simulated. This situation is rare. If the prompt is successful, the access control is not toggled. Sound, there are two cases here, the first is because your card reader does not support the phone as a card, this situation needs to use the program's write function curve to achieve simulation; second is because you did not open HCE, your phone is reading Card mode, so no credit card, the solution is to set the HCE to the nfc settings interface.
6. If your access card cannot be read with a mobile phone, your access card may be an ID card. NFC hardware only supports IC cards. For ID card access control systems, NFC hardware does not support it.
1. You don't need root to write the card, but you need to purchase a special white card from the author, then simulate your access card with the white card to swipe the card. The white card can be erased indefinitely.
2, the author provides a variety of styles of white cards, later will also launch rings, pendants, implanted chips and other white cards to meet your different needs.
3, now you can go to get your access control card to swipe, in the main interface of the program to swipe, the program will automatically save the card, and then click [start writing], the program will enter the write card status, this time will be a special white card On the mobile phone reader, the program will be automatically written. If the prompt is written successfully, then basically your operation is already correct.
4, then take the white card to brush the access control, if you still can not successfully open the door, please pay attention to the software tribe or Q group for help.
NFC Access Card Simulator Usage Notice1, individual models if you use supersu will be specially catered, this time you can install kingroot and other third-party rights management software, known PRO5 with supersu will be caton, can be solved with kingroot;
2, some models need to unlock the system to read the system files, the software built a key to unlock, can be seen in the environment detection;
3, if the program flash back, may be incompatible with the old and new versions of data, in this case please clear the program data, re-run, you can also uninstall the original version (equivalent to clearing the data), download and install the latest version;
4, after the simulation is successful, the system will automatically restart nfc;
5, the program built-in universal adapter file, if your phone can not use the common file, you can right-slide the main interface, click the [fit file] button to manually add the adaptation file;
6. For the first simulation, the program will save the initial NFC control file, and click a key to restore, and the system NFC control file can be restored to the initial state;
7, the program can upload card data to the server, if you want to upload new card data, please download and organize again upload, or else the latest upload will overwrite the data on the server;
8, most models black screen status is unable to swipe, you need to bright screen or even unlock to brush, known meters 3 can black card;
9. Simulated successful swiping without response: Some intelligent access control systems can recognize that the card is analog. For security reasons, it won't open the door. This situation needs to be simulated by writing software;
10, simulation of successful credit card no response: some mobile phones default reader mode, you need to set HCE in the NFC settings interface, so that the phone is in the card simulation mode to credit card;
The above is a smart lock Chinese network Xiaobian published NFC access card emulator download and installation methods and instructions for use, this article is shared by the Forum users, more access control knowledge, please pay attention to the site related content!
March 08, 2024
November 29, 2023
इस आपूर्तिकर्ता को ईमेल
March 08, 2024
November 29, 2023
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
